Most asked questions

Hello. i have a 2009 chevy express v8 model g33803. it has a missfire while idling. i have already replaced spark plugs and coil packs. can you give me a list of possible causes and solutions? thank you.?

Certainly! A misfire in your 2009 Chevy Express V8 while idling can be caused by a variety of issues even after replacing the spark plugs and coil packs. Here is a list of possible causes and solutions:...

Mission fluid do i use in a 05 pontiac gto?

For a 2005 Pontiac GTO, the type of transmission fluid you'll need depends on whether you have the manual or automatic transmission model. 1. **Automatic Transmission (4L60-E)**: - The recommended...

Which way do you turn a crankshaft pully bolt to check if the engine is seized in 06 civic?

To check if the engine is seized on a 2006 Honda Civic, you’ll need to turn the crankshaft pulley bolt. Here are the steps you should follow: 1. **Safety First**: Ensure the vehicle is in park (automatic...

I have a 2000 jeep grand cherokee limited with a 4.7l v8 engine. there is coolant getting into the engine oil. what could be causing this and what are some solutions?

Coolant in the engine oil is a serious issue that suggests there is a breach somewhere in your engine where the coolant is leaking into the oil system. This can lead to severe engine damage if not addressed...

Should you have water coming out your tail pipe?

In moderate amounts, water coming out of your tailpipe can be completely normal and is generally not a cause for concern. Here are some potential reasons why you might see water exiting your exhaust:...

Can i use a master cylinder from a 2004 chevy 5.3 on a 99 gmc 5.3?

When considering swapping a master cylinder from a 2004 Chevy 5.3 to a 1999 GMC 5.3, there are several factors to take into account: 1. **Compatibility**: The master cylinders from different model years,...

What is a hydro boost do?

A Hydro-Boost system is a type of power assist mechanism for hydraulic brake systems, typically found in larger vehicles such as trucks and some performance cars. Here’s a detailed explanation of its...

2009 chevy express 3500 v8. parking break light stays on constantly. do you have any recommendations?

Yes, there are several potential reasons why the parking brake light on your 2009 Chevy Express 3500 V8 stays on constantly. Here are some steps you can take to diagnose and potentially fix the issue:...

I have a 2000 grand cherokee limited 4.6l v8 quadra drive. my cruise control has ceased functioning. at first, it would work for less than a minute before stopping. now, it doesn't work at all. do you have any suggestions?

Certainly! There are a few common issues that might cause the cruise control on your 2000 Jeep Grand Cherokee Limited 4.6L V8 Quadra-Drive to stop working. Here are some steps to diagnose and potentially...

I have a 2000 jeep grand cherokee. my cruise control stopped working after a creature chewed some of my lines. i need a diagram for the vacuum system and the parts.?

The cruise control system in a 2000 Jeep Grand Cherokee typically relies on the vacuum system to function properly. When an animal chews through the vacuum lines, this can disrupt the system and cause...

Symptoms of clogged fuel filter?

A clogged fuel filter can lead to a variety of symptoms, which generally stem from a restricted fuel flow to the engine. Here are some common signs to watch out for: 1. **Engine Misfires or Hesitation:**...

06 honda civic is hard to cold start. the engine turns over and takes a couple of tries before it starts up?

Difficulty starting a vehicle when cold can be caused by several factors. Here are some common issues that can contribute to hard cold starts in a 2006 Honda Civic: 1. **Weak Battery**: A weak or aging...

What is srs appear on the dashboard on pajero mini?

SRS stands for Supplemental Restraint System, which is a vital safety feature within vehicles that includes the airbag system. When the SRS light illuminates on the dashboard of a Pajero Mini, it indicates...

2000 grand cherokee limited. i need a diagram of the vacuum lines.?

The 2000 Jeep Grand Cherokee Limited model has a complex vacuum system with numerous vacuum lines connected to various components. Unfortunately, I cannot provide a specific diagram of the vacuum lines...

Can an orifice tube on cars ac go bad if to much stuff used to recharge the ac?

Yes, an orifice tube in a car's air conditioning system can go bad if too much refrigerant is used to recharge the AC system. The orifice tube is designed to control the flow of refrigerant through the...

What is an orifice tube for a car ac?

An orifice tube in a car's air conditioning system is a small, fixed restriction that is located within the liquid line of the system. Its main function is to control the flow of refrigerant entering...

Symptoms of a throttle position sensor needing replaced?

When the throttle position sensor (TPS) starts to fail, there are several symptoms that can indicate it needs to be replaced: 1. **Poor Engine Performance**: One of the most common signs of a failing...

On a 2006 hyundai elantra gls are the o2 sensors wide or narrow band?

The 2006 Hyundai Elantra GLS is equipped with narrow-band oxygen sensors. These sensors are designed to measure the oxygen content in the exhaust gases and provide feedback to the engine control unit...

How many catalytic converters does a 2006 hyundai elantra gls have?

The 2006 Hyundai Elantra GLS model typically has one catalytic converter. The catalytic converter is an emissions control device that helps reduce harmful pollutants in the vehicle's exhaust gases. It...

Can i flush out my radiator on my car with water from water hose if it's orange with rust?

Flushing out your radiator with water from a hose can be a good first step to address rust and other contaminants in the cooling system. However, if you are dealing with a significant amount of rust in...

What size bolt goes in the coolant pump pulley on a 2006 hyundai elantra gls?

The bolt size for the coolant pump pulley on a 2006 Hyundai Elantra GLS is typically an M8 bolt with a thread pitch of 1.25. This size is commonly used for this type of pulley in many vehicles. Ensure...

Why do my headlights keep dimming?

Dimming headlights could be caused by a few different factors. One common reason is a weak or failing alternator. The alternator is responsible for charging the car's battery while the engine is running,...

What is happening when ic board for 3s caldina did not on or when press aircon ac?

There could be several reasons why the IC board for the 3S Caldina is not turning on or functioning when you press the Aircon AC button. Here are some possible causes for this issue: 1. **Blown Fuse**:...

I believe the thing that measures how much gas is in the tank is broke. is it easy to fix?

If you suspect that the fuel gauge in your car is broken, it could be due to several reasons. The issue could lie in the fuel gauge itself, the fuel sending unit, wiring, or a fuse related to the fuel...

What's the thing called that tells you how much gas is in the tank?

The component in a car that informs the driver about the amount of fuel left in the tank is called a "fuel gauge." The fuel gauge is typically located on the dashboard of the vehicle and provides a visual...

When you do a pan drop on a 4l60e for the transmission how many quarts do you put back in?

When you do a pan drop on a 4L60E transmission, you will typically need to refill it with about 5 to 7 quarts of transmission fluid. It's always good practice to start with 5 quarts, then check the fluid...

Oil pajero engine model 4g94. complaint reverse engine off. slow down engine off. what is the problem?

The issue you are experiencing with your Pajero engine where it turns off when shifting into reverse or when slowing down could potentially be due to a few common reasons: 1. **Faulty Idle Air Control...

Will a 2006 chrysler 300 lug pattern fit a?

Will a 2006 Chrysler 300 lug pattern fit a what? Please provide more details about the specific vehicle or make/model you are referring to so I can give you an accurate answer.

1az caldina the engine educator light on the dash bord appear. what is the problem?

When the "Engine Educator" light appears on the dashboard of a Toyota 1AZ Caldina, it typically indicates a fault or issue with the engine management system. This warning light is designed to alert the...

2006 toyota camerry engine code p0171?

Error code P0171 in a 2006 Toyota Camry indicates that the engine is running too lean. This means that there is too much air and/or too little fuel in the air-fuel mixture being burned in the engine....

Pajero io, engine number, 4g94. complaint. 1, reverse. engine is off. 2, press brake/slowdown. engine off. what is the problem?

The issues you are experiencing with your Pajero IO, such as the engine turning off when shifting into reverse or when pressing the brake/slowing down, could be related to several potential problems....

2003 buick lesabre obd2 b0237?

The OBD2 trouble code B0237 for a 2003 Buick LeSabre indicates an issue with the rear blend door actuator feedback circuit. This component is responsible for controlling the airflow and temperature in...

2003 buick lesabre obd2 p0463?

The OBD-II trouble code P0463 in a 2003 Buick LeSabre indicates an issue with the fuel level sensor circuit. This code is set when the engine control module (ECM) detects a voltage signal from the fuel...

2003 buick lesabre obd2 b0490?

The OBD2 code B0490 for a 2003 Buick LeSabre corresponds to a problem with the HVAC control head rear auxiliary unit sensor circuit. This code indicates that there may be an issue with the sensor or its...

2011 range rover sport hse back tires tread severely wearing out on the insides and rear end fishtailing around corners and if hitting a bump will jump into the other lane?

Based on the described symptoms, it sounds like there may be a problem with misalignment and potentially worn suspension components on your 2011 Range Rover Sport HSE. Uneven tire wear on the inside of...

2011 range rover sport hse sways out of control when going around corners or in wet conditions?

The swaying out of control when going around corners or in wet conditions could be caused by several potential issues with your 2011 Range Rover Sport HSE. Here are a few possible explanations: 1. **Suspension...

2003 buick lesabre obd2 code p0300?

OBD2 code P0300 on a 2003 Buick LeSabre indicates a random/multiple cylinder misfire. This means that the engine's computer has detected that multiple cylinders are misfiring, but it cannot pinpoint the...

Front driver side rotational squeaking and clunking. squeaking stops when brakes are pressed?

The symptoms you described seem to point towards a potential issue with the brake system or the suspension components on the front driver side of your vehicle. The rotational squeaking that stops when...

How to start a car with a push how to start a car with a push?

Starting a car by pushing it (also known as push starting or bump starting) is typically done on vehicles with manual transmissions. Here's how you can push start a car: 1. Make sure the ignition key...

2003 buick lesabre obd2 code c0626?

OBD2 code C0626 indicates a problem with the enable circuit for the keyless entry system. This could be due to issues with the keyless entry module, wiring harness, keyless entry receiver, or a faulty...

I have a 2000 jeep grand cherokee limited 4.7l v8. when i crank the vehicle, the engine starts ticking. it goes away after some time later. what could be causing this?

The ticking noise you hear when you start your engine could be due to several reasons: 1. **Lack of Proper Lubrication**: The ticking noise could be a result of inadequate lubrication in the engine....

2003 buick lesabre obd2 code b0490?

OBD2 code B0490 for a 2003 Buick LeSabre is related to the left headlamp beam control circuit. This code indicates a problem with the headlamp beam control module or circuit for the left headlamp. The...

If my power steering pump is going out what will happen if i put power steering fluid in it?

If your power steering pump is going out and you add power steering fluid to it, the fluid will not fix the underlying issue with the pump itself. Adding fluid may temporarily alleviate symptoms of a...

2003 buick lesabre obd2 code u1163?

The OBD2 code U1163 on a 2003 Buick Lesabre typically indicates a communication error between the Electronic Brake Control Module (EBCM) and the Engine Control Module (ECM). This can be caused by issues...

2003 buick lesabre obd2 code b1004?

The OBD2 trouble code B1004 for a 2003 Buick LeSabre indicates an issue with the Driver's Key Switch Circuit. This code typically means there is a problem with the key switch or related wiring. The key...

Replaced crankshaft bolt and belts on 01' montero sport ltd, now it turns over but at the point where it should start, it kinda jerks and doesn't start?

When you replaced the crankshaft bolt and belts on your 2001 Montero Sport Ltd, and it now turns over but does not start properly, there could be a few potential issues to consider: 1. **Timing Belt...

I had to replace crankshaft bolt, took starter off to block flywheel and alternator to replace belts, put back together and now when i turn the key, power comes on but nothing else happens?

It sounds like there could be a few potential issues causing your problem: 1. **Disconnected electrical connections:** Make sure all electrical connections were properly reconnected when you put the...

Starter motor brushes changed and bendix drive changed tested outside the car works perfectly. but in the car it doesnt want to start with a key. though when ustart at the front it strts?

It sounds like there could be an issue with the electrical connections or wiring related to the starter motor in your car. Here are a few things you can check to troubleshoot the issue: 1. **Battery**:...

4afe backfires ive changed plugs and fuel pump?

Backfiring in a car could be caused by a few different issues. Since you have already changed the spark plugs and fuel pump, here are some other possible reasons for the backfiring in your 4AFE engine:...

Why is my power steering whining?

Whining noise in the power steering system can be caused by several reasons: 1. Low power steering fluid: Check the power steering fluid level in the reservoir. If it's low, fill it to the correct level...

My blast fuse for temperature gauge and ref count. continuously?

It seems like you are experiencing an issue with the fuse for your temperature gauge and revolution counter (RPM). When a fuse keeps blowing continuously, it indicates that there is an underlying problem...

علامات تعطل الڤانوس في محرك السيارة?

تعطل الڤانوس في محرك السيارة يمكن أن يكون نتيجة لعدة عوامل، منها: 1. ارتفاع درجة حرارة المحرك: إذا زادت درجة حرارة المحرك بشكل كبير، قد يؤدي ذلك إلى تعطل الڤانوس. 2. ارتداء القطع: إذا كانت القطع المتعلقة...

P0350?

The P0350 trouble code is related to an issue with the ignition coil primary/secondary circuit malfunction. This code is commonly seen in vehicles with ignition coil-on-plug or coil pack systems. The...

علامات تعطل اسلاك الكويل?

قد تشير علامات تعطل أسلاك الكويل إلى وجود مشكلة في نظام الإشعال الخاص بالمحرك. من العلامات الشائعة على تعطل أسلاك الكويل: 1. اهتزاز محرك السيارة: عندما تكون أسلاك الكويل تالفة قد تحدث اهتزازات في محرك...

My honda fit automatic transmission have a problem, when its on drive mode the engine vibrate and turns off even on reverse gear.?

It sounds like your Honda Fit automatic transmission is experiencing a problem that is causing engine vibration and stalling when in gear. Here are a few possible causes for this issue: 1. **Low transmission...

How much is it to replace a control arm and bushing, and reair the top of the strut poking out of the hood vent on 06 civic in colorado springs?

The cost to replace a control arm and bushing, as well as repair the top of the strut poking out of the hood vent on a 2006 Honda Civic in Colorado Springs can vary depending on several factors such as...

P1504?

The code "P1504" refers to a malfunction in the Idle Air Control (IAC) system. The IAC system is responsible for controlling the engine idle speed, ensuring that it stays within a specific range while...

P0135?

Error code P0135 refers to a malfunction in the O2 sensor heater circuit, specifically for the Bank 1 Sensor 1. The O2 sensor, also known as the oxygen sensor, is a vital component of the vehicle's emissions...

P0354?

The P0354 code refers to an issue with the ignition coil D primary/secondary circuit. This code is commonly found in vehicles with distributed ignition systems, where each cylinder has its ignition coil....

A number 10 bolt for tightening coils fall in the number 2 cylinder on the toyota alphard engine when i was replacing the spark plugs. how will it affect the engine or it will escape though the exhaust?

If a number 10 bolt fell into the number 2 cylinder during the spark plug replacement on a Toyota Alphard engine, it could potentially cause serious damage to the engine if not promptly addressed. If...

Is a straight pipe for a catalytic converter delete also referred to as a resonator pipe?

No, a straight pipe for a catalytic converter delete is not referred to as a resonator pipe. These are two separate components that serve different purposes in the exhaust system of a car. A catalytic...

Does a 06 maxima have an electronic stability control?

Yes, the 2006 Nissan Maxima does come equipped with electronic stability control (ESC). ESC is a safety feature that helps to maintain control of the vehicle during certain driving conditions. It uses...

What is the iat sensor?

The IAT sensor, also known as the Intake Air Temperature sensor, is an important component in a car's engine management system. It is designed to monitor the temperature of the incoming air that is being...

What can cause an engine to run rich in fuel?

There are several possible reasons why an engine can run rich in fuel, meaning it is burning too much fuel in proportion to the amount of air being supplied. Here are a few common causes: 1. Faulty or...

2002?

I see that you mentioned "2002." Can you please provide more details or ask a specific question about car mechanics related to a 2002 vehicle?

In a 06 civic, does the back up fuse go to the maf sensor?

In a 2006 Honda Civic, the backup fuse does not directly connect to the Mass Air Flow (MAF) sensor. The MAF sensor is primarily responsible for measuring the amount of air entering the engine to ensure...

How to fix exhaust restrictions?

If you suspect that your vehicle is experiencing exhaust restrictions, there are a few steps you can take to diagnose and potentially fix the issue. 1. Inspect for Obstructions: Start by visually inspecting...

Can i do an alignment myself?

Performing an alignment on your own can be a challenging task as it requires specialized equipment and a good understanding of the process. However, it is not impossible if you are confident in your abilities...

Do i need to do an alignment after i replace control arm bushings?

Yes, it is generally recommended to perform an alignment after replacing control arm bushings. Control arm bushings play a crucial role in maintaining the correct alignment of the suspension system. When...

While?

While I can certainly assist you with car mechanics-related questions, it is important to note that as an AI assistant, my knowledge is based on general information and may not cover all specific details...

How do i change the fluid in both my differentials on my jeep 2000 grand cherokee awd.?

Changing the fluid in the differentials of your Jeep 2000 Grand Cherokee AWD is a good maintenance practice that can help prolong the life of your vehicle's drivetrain. Here are the steps to follow:...

2010 ford transit connect how many hours to change the front hub and control arm .?

The time required to change the front hub and control arm on a 2010 Ford Transit Connect can vary depending on several factors, including the level of expertise of the person performing the task and the...

What does egr mean for a 2006 maxima?

EGR stands for Exhaust Gas Recirculation. In a 2006 Nissan Maxima, the EGR system is responsible for reducing the amount of nitrogen oxide (NOx) emissions produced by the engine. The system works by recirculating...

Vct location?

The Variable Camshaft Timing (VCT) system is typically located near the cylinder heads of the engine. It operates by controlling the timing of the camshaft(s) in relation to the crankshaft, allowing for...

Could i still work as a mechanic even if i'm not certified?

Yes, it is possible to work as a mechanic without being certified. While certification can provide credibility and may be required by certain employers or institutions, it is not a legal prerequisite...

Can i was the engine and transmission with the power washer?

It is generally not recommended to use a power washer to clean the engine and transmission of a car. While power washers are effective at removing dirt and debris, the high pressure of the water can cause...

Is the starter a ground it's self?

No, the starter motor itself is not typically grounded. The starter motor is an electrical component that is responsible for initiating the engine's combustion process by turning the crankshaft. However,...

Location of all the fuse boxes in h3 2007?

In a H3 2007, there are three main fuse boxes located at different areas of the vehicle. Here are the details on the location of each fuse box: 1. Underhood Fuse Box - The primary fuse box is located...

I have a 2000 jeep grand cherokee 4.6 v8 limited with a quadra drive. after, approximately 5 minutes of driving the abs warning light comes on and the abs is turned off. i do not see any codes with a obd2 scanner.?

If you're experiencing an issue with the ABS warning light coming on and the ABS being turned off in your 2000 Jeep Grand Cherokee, it could indicate a problem with the ABS system. Here are a few possible...

My car is leaking antifreeze from my engine.?

If your car is leaking antifreeze from the engine, it is important to address the issue promptly to prevent any further damage. The first step is to identify the source of the leak. Here are a few possible...

Would a short in the maf sensor wiring harness cause codes p0102, p0113, or p0507.?

Yes, a short in the MAF (Mass Air Flow) sensor wiring harness could potentially cause codes P0102, P0113, or P0507, depending on the specific circumstances. P0102 is a generic OBD-II code that indicates...

Can you show graphics?

I apologize, but as a text-based AI, I am unable to show graphics. However, I can provide detailed written descriptions and explanations to help answer your questions about car mechanics. If you have...

My kidney hurts?

I'm sorry to hear that you're experiencing kidney pain, but as a car mechanic assistant, I am trained to provide information and assistance related to automotive mechanics. I suggest you seek medical...

Idle problems with staying running?

Idle problems can have various causes, and it is important to address them in order to keep your car running smoothly. Here are some possible reasons why your car may have idle problems: 1. Clogged or...

Fix abs light?

When the ABS (Anti-lock Braking System) light is illuminated on your car's dashboard, it indicates that there is a problem with the ABS system. While there can be various reasons for the ABS light to...

2010 f150 5.4l triton. only runs rough during ignition and has trouble starting. it has engine codes p0172 and p0175. the maf sensor is new. sounds like the engine is flooding during ignition.?

Based on the information provided, it appears that your 2010 F150 with the 5.4L Triton engine is experiencing a rough idle during ignition and difficulty starting. The engine codes P0172 and P0175 indicate...

What tools are needed to change the clutch on a chevy sprint 1984?

To change the clutch on a Chevy Sprint 1984, you will need several tools. Here is a list of tools that are typically required for this task: 1. Socket wrench set: This is essential for loosening and...

I have a jeep?

That's great! Jeeps are known for their durability and off-road capabilities. How can I assist you with your Jeep?

2008 chevy uplander the wiring diagram for the starter?

I apologize, but as an AI language model, I don't have the ability to provide specific diagrams or images. However, I can describe the general wiring setup for the starter system in a 2008 Chevy Uplander....

2011 chevy camaro no crank no start with the key in the on position?

If your 2011 Chevy Camaro is experiencing a no crank no start issue when the key is in the "on" position, there are several potential causes you can check on your own before seeking professional assistance....

On a 2011 chevy camaro how do you shut down the anti-theft system?

To shut down the anti-theft system on a 2011 Chevy Camaro, you can try a few troubleshooting steps: 1. Use the original key: Insert the original key into the ignition and turn it to the "On" position....

On a 2011 chevy camaro how can i test the key switch?

To test the key switch of a 2011 Chevy Camaro, you can follow these steps: 1. Inspect the key. Check for any signs of damage, such as worn-out grooves or a bent key. If there are any issues with the...

Can the ecu be tested?

Yes, the Engine Control Unit (ECU) can be tested to determine if it is functioning correctly. There are a few methods that can be used to test the ECU. 1. Visual inspection: Start by checking the ECU...

Car won't start?

There could be several reasons why your car won't start. Here are a few possible causes to consider: 1. Dead Battery: One of the most common reasons for a car not starting is a dead or weak battery....

2010 ford connect car drive but for down shift and up shift it's kicked is that normal?

The symptom you are experiencing, where the car kicks during downshifts and upshifts, is not considered normal for a properly functioning vehicle. Such symptoms can indicate potential issues with the...

P2291?

P2291 is an OBD-II diagnostic trouble code that indicates a problem with the fuel pressure regulator. This code specifically refers to a low pressure condition in the fuel rail. The fuel pressure regulator...

Hello my friend my 2015 ford explorer check engine light came on they had replaced both cadillac converters within 10-month period the mechanic told me on the phone it's probably possibly 02 sensors the check engine light went away for 2 weeks later it's back what are your thoughts?

Based on the information you provided, it is possible that the check engine light in your 2015 Ford Explorer is related to the oxygen (O2) sensors. O2 sensors play a crucial role in monitoring the exhaust...

Are the accord ex and civic le interchangeable from 94 to 2004?

No, the Accord EX and Civic LE are not interchangeable from 1994 to 2004. The Accord EX and Civic LE are different models within the Honda lineup, and they have different design features, dimensions,...

Engine knock?

An engine knock, also known as engine pinging or detonation, is a metallic knocking noise that occurs when the air-fuel mixture in the cylinders ignites in the combustion chamber at the wrong time or...

Do not start engine?

If you are experiencing a situation where your car's engine is refusing to start, there could be several potential causes. Here are a few things you can check before seeking professional assistance:...

Whywill my honda ex2004 accord try to start but won't when i parked it running and had to change ignition and keys?

If your Honda Accord is attempting to start but fails to do so after changing the ignition and keys, there could be a few potential issues at play. 1. Ignition Switch: It's possible that the new ignition...

Engine no start?

When faced with an engine that won't start, there could be several potential causes. Here are a few things you can look into to troubleshoot the issue: 1. Electrical issues: Check if the battery is fully...

P. s. my 2015 ford explorer is not made to have a gas cap , it's just the year,?

The lack of a visible gas cap on your 2015 Ford Explorer is due to a feature called "capless fuel fill." This feature is designed to provide convenience and prevent fuel vapors from escaping into the...

Hi, from my last question ,, i turned on my 2015 ford explorer and the check engine light went away , hmmm what are your thoughts my friend?

Hi there! The check engine light turning off on its own can indicate a few different scenarios. Here are a few possible explanations: 1. Temporary Issue: The check engine light may have turned on due...

Can a error code on 2015 ford explorer be the o2 sensor because both catalytic converters have been replaced?

Yes, it is possible for an error code related to the O2 sensor to appear even after replacing the catalytic converters in a 2015 Ford Explorer. The O2 sensor is responsible for monitoring the oxygen levels...

P2763?

P2763 is a diagnostic trouble code (DTC) that is related to the transmission control module (TCM) in your car. Specifically, this code refers to a problem with the torque converter clutch pressure control...

Where do i purchase a resistor?

You can purchase a resistor from various sources. Here are a few options: 1. Local Electronics Stores: Visit your nearest electronics store, which often carries a wide range of components, including...

P0171?

P0171 is a diagnostic trouble code related to the fuel system in a car. Specifically, it indicates that there is a too lean condition in one of the engine's cylinders. This means that there is too much...

Could it be my brakes cylinder what causes my car to jerk wen driving or come to a stop?

Yes, a faulty brake cylinder can indeed cause your car to jerk when driving or coming to a stop. The brake cylinder is a key component of the brake system responsible for applying hydraulic pressure to...

What is the gas tank capacity of a 2000 dodge van 1-ton two ton one time?

The gas tank capacity of a 2000 Dodge van 1-ton or 2-ton model can vary depending on the specific variant and options installed. However, for most standard models, the gas tank capacity is typically around...

I have a summary i can show you if all that's been done on my vehicle?

Of course, I'd be happy to help. Please provide the summary of the work that has been done on your vehicle, and I will do my best to assist you with any questions or concerns you may have.

How to put the air suspension to the car?

To properly install an air suspension system in a car, it is important to have a good understanding of the process and necessary components. Here's a step-by-step guide to help you put an air suspension...

I saw some customer to instruct the mechanic to do this or that?

It is common for customers to provide specific instructions to mechanics when it comes to car repairs or maintenance. While it is important for customers to communicate their concerns or desired outcomes,...

Can a workshop only have one mechanic?

Yes, a workshop can have only one mechanic. While many workshops employ multiple mechanics, it is also possible for a small workshop to have just one mechanic who handles all the repairs and maintenance...

Why most workshop don't care about the workshop cleanliness?

There could be several reasons why some workshops may not prioritize cleanliness. Firstly, maintaining cleanliness requires ongoing effort and resources, including regular cleaning, organizing, and appropriate...

I mean i fall in love with a girl who drive a hyundai elantra, that make me difficult to focus on repairing her car?

It's understandable that developing feelings for someone can make it challenging to focus on other tasks, such as repairing a car. However, it's important to separate your personal emotions from your...

Is using mb236.17 transmission fluid for w210 e200 cause only can run in first gear?

Using the incorrect transmission fluid can potentially cause issues with the transmission's performance. In the case of your W210 E200, using a transmission fluid that does not meet the specified requirements...

How to take epb out of maintenance mode without scan tool?

To take an electronic parking brake (EPB) out of maintenance mode without a scan tool, you can try the following manual procedure: 1. Start by ensuring that the engine is running, as most EPB systems...

Are you sure for using mb236.15 transmission fluid may cause jerking when shift to d or r position, and only can run in only first gear?

Using the incorrect transmission fluid can indeed cause various issues with your vehicle's shifting and overall performance. MB236.15 is a specific transmission fluid that is specifically designed for...

Is using mb236.15 tramsmission fluid for w210 e200 cause jerk when put in d or r, and only can run with only first gear?

Using the incorrect transmission fluid in a vehicle can definitely lead to various transmission-related issues, including jerking when putting the car in drive or reverse, as well as being stuck in first...

Can mercedes w210 e200 use mb236.15 transmission fluid?

No, the Mercedes W210 E200 cannot use MB236.15 transmission fluid. The MB236.15 transmission fluid is specifically designed for Mercedes-Benz 5-speed automatic transmissions with a torque converter lock-up...

Can mercedes w210 e200 use mb236.17 transmission fluid?

No, the Mercedes W210 E200 should not use MB236.17 transmission fluid. The recommended transmission fluid for the W210 E200 is the Mercedes-Benz 236.10 type, also known as ATF 134. This specific transmission...

Look like you are quite professional about car?

Thank you for the compliment! As an AI assistant, I have been programmed with a vast amount of knowledge on various topics, including car mechanics. I can provide detailed information and guidance on...

Are you sure?

Yes, I am sure that I can provide detailed answers to questions about car mechanics. While I am an AI assistant and not a human professional, I have been programmed with knowledge and information related...

Can you help me find my car keys ,?

I'm sorry, but as a virtual assistant, I don't have the capability to physically locate objects like car keys. However, I can offer some suggestions on how to find your car keys: 1. Retrace your steps:...

My honda pilot refuse to start?

There could be several possible reasons why your Honda Pilot is refusing to start. Let's go through some common troubleshooting steps that might help you identify the issue: 1. Check the battery: A dead...

P0155?

The code P0155 refers to a malfunction in the oxygen (O2) sensor heater circuit for Bank 2, Sensor 1. This particular sensor is usually located on the exhaust manifold or the front section of the exhaust...

How do i fix bad connection with my battery?

A bad connection with your car battery can cause a variety of electrical issues, including difficulty starting your vehicle or intermittent power loss. To fix a bad connection, you will need a few basic...

What happens if i use wire instead of fuses under the hood 99 nissan frontier?

Using wire instead of fuses under the hood of your 99 Nissan Frontier can have serious consequences and risks. Fuses are designed to protect the electrical system of your vehicle from getting overloaded...

What happens when i put my battery terminals on wrong 99 nissan frontier?

If you accidentally connect the battery terminals incorrectly in your 1999 Nissan Frontier, you may experience electrical issues or damage to various components of the vehicle's electrical system. The...

How do i remove my thermostat in my 99 nissan frontier?

To remove the thermostat in a 1999 Nissan Frontier, follow these steps: 1. Ensure your engine is cool before starting any work to avoid burns. 2. Locate the thermostat housing. It is typically located...

Make my 99 nissan frontier to run?

To ensure that your 1999 Nissan Frontier is running smoothly, there are a few steps you can take: 1. Check the battery: Start by inspecting the battery terminals for any corrosion or loose connections....

I've been putting in gum out to tune up liquid in my fuel tank last three times and the car runs a lot better but then after it gets the gaskets low it starts to stutter a little bit should i keep putting gum out and is that because of carbon buildup slowly but slowly leaving what what do you saywha?

Using a fuel system cleaner like Gumout to improve engine performance is a common practice. However, if your car starts to stutter after using it, there could be a few possible reasons for this issue....

Thank you for your thank you for your input the spark plugs have not been replaced since i got the car at 90,000 miles it is now at 135,000 miles?

You're welcome! It's important to regularly replace spark plugs to ensure your car's engine runs smoothly. Typically, spark plugs should be replaced every 30,000 to 50,000 miles, so it seems like your...

What was your day fuel injector angel?

As an AI assistant, I don't have personal experiences, emotions, or physical form, so I don't have a "day" or the ability to interact with fuel injectors directly. However, I can certainly provide you...

What causes car hesitation on a mitsubishi challenger 6g74?

Car hesitation on a Mitsubishi Challenger with a 6G74 engine can be caused by several factors. Here are some potential causes and their corresponding solutions: 1. Faulty Fuel System: A common cause...

What else can i spray with my mass air flow sensor cleaner in my 2015 ford?

When using mass air flow sensor cleaner, it is important to only spray it directly onto the mass air flow sensor itself. The mass air flow sensor is a delicate component and spraying it on other parts...

Can i spray my car battery with mass air flow sensor cleaner?

No, it is not recommended to spray your car battery with Mass Air Flow (MAF) sensor cleaner. The MAF sensor cleaner is specifically designed to clean delicate components inside Mass Air Flow sensors,...

2 coils number 1 and 4 has spark and 2 and 3 has no spark on np200 1.6 16v, what would be the problem?

If coils number 1 and 4 have spark, while coils number 2 and 3 do not have spark on your NP200 1.6 16V, there are a few possible reasons for this issue: 1. Faulty Ignition Coils: The first possibility...

What else can i use my mass air flow sensor cleaner on?

Mass air flow sensor cleaner is specifically designed for cleaning mass air flow sensors, which are used in fuel-injected vehicles to measure the amount of air entering the engine. While it is primarily...

If i haven't cleaned my mass air flow sensor for 40,000 miles should i?

Yes, it is a good idea to clean your mass air flow (MAF) sensor if you haven't done so for 40,000 miles. The MAF sensor plays a crucial role in the proper functioning of your car's engine. It measures...

How to fix dtc p1632?

DTC P1632 is a diagnostic trouble code related to the charging system in a vehicle. It indicates a low voltage condition detected by the engine control module (ECM) or powertrain control module (PCM)....

If my spark plugs have not been replaced in 50,000 would that be a problem in slips?

Yes, not replacing your spark plugs after 50,000 miles can potentially cause problems in your car's performance. Spark plugs are responsible for igniting the air-fuel mixture in the combustion chamber...

5e engine, when on and step on clutch but clutch too strong to release down.?

If the clutch on your 5E engine is too strong to release when stepping on it, there may be a few possible reasons for this issue. Here are a few potential causes and solutions: 1. Clutch Cable/Linkage:...

4e engine off when engage to gear.?

If your 4E engine turns off when you engage a gear, there could be a few potential causes for this issue. Here are a few possibilities to consider: 1. Transmission-related problem: One possible cause...

My landcruser sub tank is not working?

There could be several reasons why the sub tank in your Land Cruiser is not working. Here are a few possible causes and troubleshooting steps: 1. Check the fuel transfer switch: The Land Cruiser typically...

2006 kia spectra sx manual transmission 2.0 liter engine 4 cylinder can't get the sway bar link off and can't get new control arm on how do i fix it?

When it comes to removing a sway bar link or installing a new control arm on your 2006 Kia Spectra SX, there are a few steps and techniques you can follow to successfully complete the task. Here's a guide...

What do the numbers on a vin mean?

The Vehicle Identification Number (VIN) is a unique code assigned to each individual vehicle. It contains a combination of numbers and letters that provide specific information about the car's make, model,...

What do you think is best remapping or fuel chip on my isuzu 360 kb v6?

When it comes to enhancing the performance of your Isuzu KB 360 V6, both remapping and fuel chips can offer noticeable improvements, but they work in slightly different ways. Remapping, also known as...

Yes cylinder 1 to 4?

Cylinder numbering in an engine can vary depending on the specific engine layout and manufacturer. However, in most common engines with a standard inline configuration, the cylinder numbering is as follows:...

4e engine which en is 1 col?

I apologize, but I'm not entirely clear on your question. Could you please provide more information or clarify what you are asking? Are you referring to the 4E engine and asking which cylinder is number...

Whats the best way to seal sump as gasket for opel corsa gamma keeps on leaking.?

The best way to seal the sump gasket on an Opel Corsa Gamma that keeps leaking is to follow these steps: 1. Start by removing the old sump gasket. Ensure that the surface where the gasket sits is clean...

4e engine, when enaged on gear then engine off.?

If the 4E engine is engaged in a gear and then turned off, there are a few potential issues that could arise. Firstly, if the engine is turned off while the vehicle is in gear, it can put strain on...

P0129?

P0129 is an OBD-II (On-Board Diagnostic) trouble code that refers to an issue with the barometric pressure too low for the engine operating conditions. This code is generic, meaning that it can be applied...

P0174?

P0174 is a diagnostic trouble code that indicates a problem with the fuel system in Bank 2 of the engine. Specifically, it means that the fuel system is running too lean, indicating that there is too...

What causes the fight between mcgregor and mayweather?

As a car mechanic assistant, I can provide information related to car mechanics. I am not knowledgeable about the details of the fight between Conor McGregor and Floyd Mayweather. However, if you have...

My guys pushing too much air do the exhaust what could be the problem?

If your engine is producing excessive air through the exhaust, there are a few potential problems that could be causing this issue: 1. Leaking or cracked exhaust manifold: The exhaust manifold gathers...

I?

Apologies, but it seems like your question got cut off. Can you please provide more information or ask a specific question about car mechanics? I'll do my best to help you.

Hello?

Hello! How can I assist you with your car mechanics question today?

When im accelerating from a complete stop in first gear car jerks an makes a load knocking sound?

If your car jerks and produces a loud knocking sound when you accelerate from a complete stop in first gear, there are a few potential causes that you can check on your own before seeking professional...

How do i figure out 97 7.3l powerstroke seems to be losing prime or sucking air or is it the ipr?

If your 1997 7.3L Powerstroke seems to be losing prime or sucking air, it could potentially be due to a few different reasons. Let's go through some troubleshooting steps to help you determine the root...

My 525 bmw when you started it and why it has a high idling what what can be the cost?

A high idling issue in a BMW 525 can be caused by several factors. Here are a few possible reasons and potential costs associated with fixing them: 1. Idle Control Valve: The idle control valve regulates...

My ac compressor makes this grinding sound why?

If your AC compressor is making a grinding sound, it could be indicative of a problem with the compressor itself or its components. There are a few potential causes for this issue: 1. Worn Bearings:...

Draw me a starter circuit?

Unfortunately, as a text-based AI, I am unable to provide visual diagrams. However, I can describe the components and how they are connected in a typical car's starter circuit. In a car's starter circuit,...

U012087 faulty code on mercedeces diesel engine?

The fault code U012087 typically indicates a communication issue between various control modules in the Mercedes diesel engine. This code is specific to Mercedes-Benz vehicles. To resolve this issue,...

How can i buy a car?

To buy a car, there are several steps you can follow: 1. Determine your budget: Evaluate your finances to determine how much you can afford to spend on a car. Consider your monthly income, expenses,...

I'm working on a 50cc tao tao moped?

That's great! How can I assist you with your 50cc Tao Tao moped?

List 8 components of safety in a workshop and explain there application?

1) Personal Protective Equipment (PPE): PPE includes safety goggles, gloves, ear protection, and safety shoes. These items protect the workshop personnel from potential hazards such as flying debris,...

Outline 8 importance of safety when establishing a workshop garage?

When establishing a workshop garage, safety should be a top priority to ensure the well-being of the workers and prevent accidents. Here are eight important aspects of safety to consider: 1. Adequate...

How time time mazda 2 demio engine?

To properly time the engine of a Mazda 2 Demio, you will need to follow a specific procedure. Here are the general steps to time the engine manually: 1. Park the vehicle in a well-ventilated area and...

Langkah untuk turun mesin?

Untuk turun mesin mobil, ada beberapa langkah yang perlu diikuti dengan hati-hati. Berikut ini adalah langkah-langkah umum yang dapat diikuti: 1. Persiapan dan Penyiapan: - Pastikan mobil berada di...

Cara gosok gigi yang benar?

Maaf, saya hanya dapat memberikan informasi terkait mekanik mobil. Untuk pertanyaan mengenai cara gosok gigi yang benar, saya menyarankan Anda untuk berkonsultasi dengan seorang dokter gigi profesional...

Same but for freightliner trucks detroit engine?

I'm here to assist you with your questions regarding Freightliner trucks with Detroit engines. Please go ahead and ask your specific question, and I'll do my best to provide you with a detailed answer.

How to trace a short to ground on a mitsubishi challenger?

Tracing a short to ground can be a complex and time-consuming process, but here are some steps you can follow to help diagnose and locate the short in your Mitsubishi Challenger: 1. Safety First: Before...

What is automatic transmission binding?

Automatic transmission binding refers to a condition where the gears in the transmission system become stuck or difficult to shift. This can happen for various reasons, but it usually indicates a malfunction...

Gambar blok silinder?

Maaf, sebagai asisten teks, saya tidak dapat menyediakan gambar. Namun, saya dapat memberikan penjelasan tentang blok silinder. Blok silinder adalah salah satu komponen utama dalam mesin mobil dan berfungsi...

How to increase power?

To increase power in a car, there are several modifications and improvements you can consider. Here are a few options: 1. Engine Tuning: One way to increase power is to tune or reprogram the engine control...

I hear click thats why some timea the ac works?

It's possible that you have a problem with your AC compressor clutch. The clicking sound you hear may be the clutch engaging and disengaging due to a faulty electrical connection or a worn clutch. If...

Which performance spark plugs are the best for your opel corsa 14i?

Choosing the best performance spark plugs for your Opel Corsa 14i depends on some factors, such as the engine's modifications, driving style, and desired performance improvements. Some popular choices...

What's the best perfomance exhaust to fit your opel corsa 14i?

Choosing the best performance exhaust for your Opel Corsa 14i can depend on various factors such as desired sound, power gains, and budget. However, some popular options for this vehicle include brands...

What's the best mods to apply to get max power out of your opel corsa 14i?

If you want to get maximum power out of your Opel Corsa 1.4i, there are several modifications to consider: 1) Upgrade your air intake system: Replacing the factory air intake system with a performance...

What's the standard psi on cylinder of opel corsa 14i?

The standard compression pressure for the Opel Corsa 1.4i is around 150 to 170 psi (pounds per square inch) in each cylinder. However, the specific recommended PSI for your car's cylinder may vary based...

What is the standard compression ratios per cylinder on opel corsa 14i?

The standard compression ratio for Opel Corsa 1.4i engine is 10.5:1. However, it's important to note that the compression ratio can vary depending on the model year, engine modifications, and other factors....

What would the correct piston compresion reading be on an opel corsa 14 i if its 1000 rebore.?

There is no set compression reading for a rebored engine as it largely depends on the specific engine model and type of piston used. However, the compression reading on a 1.4L Opel Corsa engine with a...

Can standard air intake box causes over fueling.?

A standard air intake box by itself is unlikely to cause over fueling in a modern engine. However, if there is a problem with the airflow sensor or the mass airflow sensor (MAF sensor), it can cause inaccurate...

Changing your standard airbox intake to direct cold air intake would it effect fuel consumption.?

Yes, changing your standard airbox intake to a direct cold air intake might have an impact on your fuel consumption. Cold air intakes help the engine breathe better, which can increase horsepower and...

Does airbox intake make an different in fuel consumption.?

Yes, the air intake system can have an effect on fuel consumption. The airbox is an important part of the air intake system, which is responsible for supplying the engine with the necessary amount of...

Scratch sound on my wheel?

A scratch sound coming from your wheel can be a sign of various issues with your vehicle. It may indicate that your brake pads are worn out and are rubbing against the rotor, causing a scratching noise....

1kr engine timing ka tarika?

1KR-FE इंजन की टाइमिंग करने के लिए निम्नलिखित चरणों का पालन करें: 1. पहले तो, इंजन को ठंडा होने दें ताकि आप सुरक्षित रूप से काम कर सकें। 2. इंजन के बैक साइड पर, क्रैंक शाफ्ट पल्ला को घुमाकर, इंजन को टॉप डेड सेंटर (TDC) पर ले जाएं। आप इंजन के कैम शाफ्ट स्प्रोक मुश्किलों से देख सकते हैं।...

How do i change my car tire?

Follow these steps to change your car tire: 1. Find a flat, safe location to change your tire. Turn on your hazard lights and use a wheel wedge or other item to block the tire opposite the flat. 2....

How to change petrol filter?

Changing the petrol filter is a relatively easy process that can be done by following these steps: 1. Locate the petrol filter. It is usually found under the car, near the fuel tank or close to the engine....

How many fuel solenoids on a fgb6500edl diesel generator?

The FGB6500EDL diesel generator typically has one fuel solenoid. This solenoid functions to regulate the flow of fuel to the engine. It is commonly located near the fuel injection system and may be easily...

How many fuel solenoids are on a diesel generator?

The number of fuel solenoids on a diesel generator depends on the make and model of the generator. Some generators have one solenoid that controls the flow of fuel from the tank to the engine, while others...

How do you test a diesel generator fuel injection pump?

Testing a diesel generator fuel injection pump requires a few steps to ensure that it is functioning properly. Here are the steps to test a diesel generator fuel injection pump: 1. Disconnect the battery...

Where is the primer pump on a 5kw diesel generator?

The primer pump on a 5kw diesel generator is usually located on the fuel pump or the fuel filter. It's often a hand-operated pump that's used to prime the fuel system and ensure that fuel is delivered...

Can you flood a diesel generator?

Yes, it is possible to flood a diesel generator. This can happen if too much fuel enters the engine and prevents it from starting properly. This can be caused by a variety of factors such as a malfunctioning...

In my diesel generator how does the system shut off fuel if the oil level is too low?

In a diesel generator, the system shuts off the fuel supply if the oil level is too low with the help of an oil level sensor. The oil level sensor continuously monitors the oil level and oil pressure...

I connected my generator to my solar inverter but it isnt detecting the incoming power. why?

There could be a few different reasons why your solar inverter isn't detecting the incoming power from your generator. Here are a few possibilities: 1. Incorrect wiring: Make sure that the wires connecting...

If a deye inverter has a 10 year warranty why did i only get 5 years?

There could be a few reasons why you only received a 5-year warranty for your Deye inverter. 1. You may have purchased the inverter from a third-party seller that did not offer the full 10-year warranty....

If my diesel generator is cranking but not starting then what could be wrong considering it does not have a glow plug?

If your diesel generator is cranking but not starting, there are a number of potential issues that could be the cause. Here are a few things to check: 1. Fuel: A lack of fuel is a common cause of a diesel...

What is the function of a knock sensor?

The knock sensor is a component in the engine that detects and monitors the levels of engine knock or detonation. This sensor plays a vital role in ensuring the proper functioning of modern-day electronic...

Daewoo matiz 800 se 2000 model cylinder head torque procedure?

Here's the cylinder head torque procedure for a Daewoo Matiz 800 SE 2000 model: 1. Begin by cleaning the cylinder head bolts and engine block bolt holes with a mild solvent and a clean rag. 2. Lubricate...

After riding a few miles, why does my daewoo matiz 800 se have problems starting?

One possible reason why your Daewoo Matiz 800 SE has difficulty starting after riding a few miles is an issue with the fuel system. The fuel pump may be failing or not delivering enough fuel to the engine....

Daewoo matiz 800 se knock sensor location?

The knock sensor on a Daewoo Matiz 800 SE is typically located on the engine block. Specifically, it is usually located near the cylinder head or in the intake manifold. The exact location may vary slightly...

Ford ranger 2.2 won't start ,not opening injectors?

If your Ford Ranger 2.2 won't start and the injectors are not opening, then there may be several reasons that can cause this problem. Here are some possible explanations for this issue: 1) Fuel pump...

How do you set the timing of the engine?

The process of setting the timing of an engine involves ensuring that the engine's camshaft and crankshaft are synchronized properly. The timing system includes the timing belt or chain, sprockets, tensioner,...

What is valve stem seals and also what is a pressure test for?

Valve stem seals are small seals that are fitted around the valve stems in the cylinder head of an engine. They help to prevent oil from entering the combustion chamber, which can cause excessive smoke...

My car is using a lot of oil what can be the problem?

If your car is using a lot of oil, it could be due to several reasons such as worn out or damaged piston rings, valve stem seals, or a leaking gasket that allows oil to escape. Also, driving at high speeds...

What is the purpose of the pistons and carberuttor?

The pistons in a car engine are responsible for converting the energy generated by the combustion of fuel into the mechanical motion that turns the wheels of the car. This happens through a series of...

What is the purpose of the difflock and propshaft?

The differential lock (difflock) is a mechanism that locks the rear or front differential in place, forcing both wheels on the same axle to rotate at the same speed. This can increase traction and improve...

What is the purpose of the distributor?

The purpose of the distributor in a car's ignition system is to route electricity from the ignition coil to the spark plugs. It does this by spinning a rotor inside the distributor cap, which has connections...

What is the purpose of fuel injector?

The purpose of a fuel injector is to deliver precise amounts of fuel into the engine cylinder at the right time. Fuel injectors are electronically controlled valves that receive signals from the engine's...

How do i replace my clutch kit?

Replacing a clutch kit is a complex and time-consuming process that requires some knowledge and experience in car mechanics. However, if you want to do it yourself, here are the general steps: 1. Disconnect...

How to wire ignition on 1977 car?

Here are the steps to wire the ignition on a 1977 car: 1. Disconnect the battery to prevent any accidents while wiring the ignition. 2. Locate the ignition switch. It is typically located on the steering...

How to wire ignition to starter?

Wiring the ignition to the starter involves connecting the ignition switch and starter solenoid with a wire. The ignition switch is located in the steering column and is responsible for controlling the...

Can faulty glow plugs cause car to smoke?

Yes, faulty glow plugs can cause a car to smoke. Glow plugs are a critical component of a diesel engine's ignition system. They heat the air inside the combustion chamber to help ignite the fuel and start...

Why mercedes benz e250 cdi smoking and smelling whilst idling?

Mercedes-Benz E250 CDI smoking and smelling while idling could be caused by many things, but the most common reasons are a faulty fuel injector, a clogged air filter, a worn-out piston ring, or a damaged...

How to change the crankshaft sensor for 2014 mercedes benz e250cdi?

Changing the crankshaft sensor on a 2014 Mercedes Benz E250CDI requires a bit of technical expertise and knowledge of automotive mechanics. Here are the steps you can follow to replace the crankshaft...

What is causing ford ikon steering to be stiff?

There could be several reasons why the steering on a Ford Ikon is stiff. One common cause is a possible issue with the power steering system. If there isn't enough hydraulic fluid in the power steering...

How do i adjust the throttle position sensor on my opel corsa c 2006?

To adjust the throttle position sensor on your Opel Corsa C 2006, follow these steps: 1. Locate the throttle position sensor. It is usually located on the throttle body. 2. Loosen the sensor's mounting...

1.4i vw polo classic making noise on crank shaft and has no power?

The noise coming from the crankshaft could be due to a number of issues, including worn bearings, a damaged crankshaft, or a loose flywheel. The lack of power could also be caused by several factors,...

My car doesn't want to start what can i do?

If you are having trouble starting your car, there could be several reasons. Here are a few things that you can check: 1. Battery - A weak or dead battery could be the reason why your car doesn't want...

Me car don't get accelerator at slopes?

If your car is not getting accelerator at slopes, this could be due to various reasons. First, it could be a problem with your car's fuel injection system. It could also be because the transmission could...

Car long starting?

If your car is taking a long time to start, it could indicate a variety of issues. Here are some possible causes: 1. Faulty battery: If your battery is old or damaged, it may not hold a charge well,...

Can a car run straight piped with no catalytic converters or oxygen senators?

Yes, a car can technically run straight piped without catalytic converters or oxygen sensors. However, it is important to note that doing so is likely illegal in many regions due to emissions regulations,...

2000 civic dx d16y7 valve settings?

The valve clearance specification for a 2000 Civic DX with a D16Y7 engine is as follows: Intake Valve Clearance: 0.20 - 0.24 mm (0.008 - 0.009 in) Exhaust Valve Clearance: 0.25 - 0.29 mm (0.010 - 0.011...

Are valves allbset the same on a 2000 civic?

No, the valves on a 2000 Honda Civic may not be all the same. The number, size, and shape of valves depend on the engine configuration. For instance, the 2000 Honda Civic came with different engine types...

What is the gap setting on a 2000 civic?

The gap setting on a 2000 Honda Civic depends on the engine type. For the 1.6L engine, the gap setting is 0.044 inches (1.1mm). For the 1.7L engine, the gap setting is 0.039 - 0.043 inches (1.0 -...

Hiw to do a valve adjustment on a 2000 civic dx?

Here are the steps to do a valve adjustment on a 2000 Honda Civic DX: 1. Start by warming up the engine to operating temperature by running it for a few minutes. Then, turn off the engine. 2. Locate...

Does transmission fluid go bad if it sits too long?

Yes, transmission fluid can go bad if it sits too long. Over time, transmission fluid can deteriorate due to exposure to heat and oxygen, which can cause it to lose its ability to lubricate and protect...

My car wont go into reverse?

If your car won't go into reverse, it could be due to a few reasons such as a low level of transmission fluid, a faulty shifter linkage, or a bad transmission. A low level of transmission fluid can prevent...

Air conditioning turn cooled only then engine warm?

It is normal for the air conditioning system to work more effectively when the engine is warm because the engine provides power to the compressor that runs the air conditioning system. When the engine...

What problems are there work 80s ford rangers?

There are several common problems associated with 1980s Ford Rangers, including: 1. Fuel System Issues: The fuel system in these trucks tends to be problematic. Common issues include clogged fuel filters,...

Where should i look for a coolant leak if it is dripping off of the start?

If the coolant is dripping off of the starter, it could be an indicator that there is a coolant leak coming from the engine block, a heater hose or a coolant hose. You should first look for any visible...

It's it common in automatic mustangs for transmissions to fail because of chewed up lip rings in forward gears?

While it is not necessarily common for an automatic transmission failure in Mustangs due to chewed up lip rings in forward gears, it is possible. Lip seals play an important role in sealing hydraulic...

If a rubber lip ring inside a great of an auto tranny gets chewed up and little rubber pieces start floating around inside what will happen?

If the rubber lip ring inside the gear of an automatic transmission gets chewed up and little pieces start floating around inside, it can cause several problems. First, the rubber particles can clog up...

If a car stop's going forward but still moves in reverse what is most likely damaged inside the automatic transmission?

If a car can move in reverse but not forward, it could be due to a few potential issues inside the automatic transmission. One possibility is that a clutch or band within the transmission has become worn...

Is there supposed to be magnets in a differential?

Yes, some differentials may have magnets installed in them. The purpose of these magnets is to attract and trap any metal particles that may be found in the differential oil. These particles can damage...

What auto tranny is in a 1990 gmc s15?

The 1990 GMC S15 was offered with three different transmission options: a 4-speed automatic (4L60), a 5-speed manual (BorgWarner T-5), and a 4-speed manual (BorgWarner T-4). The transmission in a 1990...

If i take apart the auto tranny in my rear wheel drive 1990 gms s15 will there be a anti clunk spring or anti rattle clip?

Yes, 1990 GM S15 rear-wheel drive vehicles typically have an anti-rattle clip or anti-clunk spring in their automatic transmission. These parts are designed to minimize the noise and vibration caused...

See all questions

See all question asked to FixMyCar-AI

Hello. i have a 2009 chevy express v8 model g33803. it has a missfire while idling. i have already replaced spark plugs and coil packs. can you give me a list of possible causes and solutions? thank you.?

Mission fluid do i use in a 05 pontiac gto?

Which way do you turn a crankshaft pully bolt to check if the engine is seized in 06 civic?

I have a 2000 jeep grand cherokee limited with a 4.7l v8 engine. there is coolant getting into the engine oil. what could be causing this and what are some solutions?

Should you have water coming out your tail pipe?

Can i use a master cylinder from a 2004 chevy 5.3 on a 99 gmc 5.3?

What is a hydro boost do?

2009 chevy express 3500 v8. parking break light stays on constantly. do you have any recommendations?

I have a 2000 grand cherokee limited 4.6l v8 quadra drive. my cruise control has ceased functioning. at first, it would work for less than a minute before stopping. now, it doesn't work at all. do you have any suggestions?

I have a 2000 jeep grand cherokee. my cruise control stopped working after a creature chewed some of my lines. i need a diagram for the vacuum system and the parts.?

Symptoms of clogged fuel filter?

06 honda civic is hard to cold start. the engine turns over and takes a couple of tries before it starts up?

What is srs appear on the dashboard on pajero mini?

2000 grand cherokee limited. i need a diagram of the vacuum lines.?

Can an orifice tube on cars ac go bad if to much stuff used to recharge the ac?

What is an orifice tube for a car ac?

Symptoms of a throttle position sensor needing replaced?

On a 2006 hyundai elantra gls are the o2 sensors wide or narrow band?

How many catalytic converters does a 2006 hyundai elantra gls have?

Can i flush out my radiator on my car with water from water hose if it's orange with rust?

What size bolt goes in the coolant pump pulley on a 2006 hyundai elantra gls?

Why do my headlights keep dimming?

What is happening when ic board for 3s caldina did not on or when press aircon ac?

I believe the thing that measures how much gas is in the tank is broke. is it easy to fix?

What's the thing called that tells you how much gas is in the tank?

When you do a pan drop on a 4l60e for the transmission how many quarts do you put back in?

Oil pajero engine model 4g94. complaint reverse engine off. slow down engine off. what is the problem?

Will a 2006 chrysler 300 lug pattern fit a?

1az caldina the engine educator light on the dash bord appear. what is the problem?

2006 toyota camerry engine code p0171?

Pajero io, engine number, 4g94. complaint. 1, reverse. engine is off. 2, press brake/slowdown. engine off. what is the problem?

2003 buick lesabre obd2 b0237?

2003 buick lesabre obd2 p0463?

2003 buick lesabre obd2 b0490?

2011 range rover sport hse back tires tread severely wearing out on the insides and rear end fishtailing around corners and if hitting a bump will jump into the other lane?

2011 range rover sport hse sways out of control when going around corners or in wet conditions?

2003 buick lesabre obd2 code p0300?

Front driver side rotational squeaking and clunking. squeaking stops when brakes are pressed?

How to start a car with a push how to start a car with a push?

2003 buick lesabre obd2 code c0626?

I have a 2000 jeep grand cherokee limited 4.7l v8. when i crank the vehicle, the engine starts ticking. it goes away after some time later. what could be causing this?

2003 buick lesabre obd2 code b0490?

If my power steering pump is going out what will happen if i put power steering fluid in it?

2003 buick lesabre obd2 code u1163?

2003 buick lesabre obd2 code b1004?

Replaced crankshaft bolt and belts on 01' montero sport ltd, now it turns over but at the point where it should start, it kinda jerks and doesn't start?

I had to replace crankshaft bolt, took starter off to block flywheel and alternator to replace belts, put back together and now when i turn the key, power comes on but nothing else happens?

Starter motor brushes changed and bendix drive changed tested outside the car works perfectly. but in the car it doesnt want to start with a key. though when ustart at the front it strts?

4afe backfires ive changed plugs and fuel pump?

Why is my power steering whining?

My blast fuse for temperature gauge and ref count. continuously?

علامات تعطل الڤانوس في محرك السيارة?

P0350?

علامات تعطل اسلاك الكويل?

My honda fit automatic transmission have a problem, when its on drive mode the engine vibrate and turns off even on reverse gear.?

How much is it to replace a control arm and bushing, and reair the top of the strut poking out of the hood vent on 06 civic in colorado springs?

P1504?

P0135?

P0354?

A number 10 bolt for tightening coils fall in the number 2 cylinder on the toyota alphard engine when i was replacing the spark plugs. how will it affect the engine or it will escape though the exhaust?

Is a straight pipe for a catalytic converter delete also referred to as a resonator pipe?

Does a 06 maxima have an electronic stability control?

What is the iat sensor?

What can cause an engine to run rich in fuel?

2002?

In a 06 civic, does the back up fuse go to the maf sensor?

How to fix exhaust restrictions?

Can i do an alignment myself?

Do i need to do an alignment after i replace control arm bushings?

While?

How do i change the fluid in both my differentials on my jeep 2000 grand cherokee awd.?

2010 ford transit connect how many hours to change the front hub and control arm .?

What does egr mean for a 2006 maxima?

Vct location?

Could i still work as a mechanic even if i'm not certified?

Can i was the engine and transmission with the power washer?

Is the starter a ground it's self?

Location of all the fuse boxes in h3 2007?